Rookie65

I think what Jo_Ann means is to set the top elevation of the grade to the distance below the 1st floor subfloor. Then you can adjust it up or down from there to match your own needs

Start with the house. Probably set your default measurements for drawing from interior wall to interior wall. It'll be easier to transfer the measurements to the plan.

When I run into something like that, I will make the soffit smaller by whatever the thickness is of the material you want it to be in each direction. Then copy the soffit, move it along the axis you need to, then change that soffit to the material you desire.

You should probably upgrade to Pro 2023. I believe this was the first version to have the multiple layout page option.

Ah, I see. Stuff like that may be best drawn manually on the section detail you will include with the plan. Especially since floor 0 can't be edited for items below. Unless you tried using the existing concrete floor, change it's thickness to what you need for your material, then in the floor finish, make that the thickness of your concrete floor? Even just a polyline with some type of fill pattern and a notation will suffice. Most of the time, the materials list created by HD is not accurate enough to bid from. Usually much better off having the people bid from the plan. As long as the material is noted in the section, they should be able to pick it up

Either try to post your plan, or take a look through the reference manual. With just images, it's impossible to see what your settings are that may be doing this.

In that view, go to the top toolbar and look for the "house" icon next to the mouse orbit tool. There you can toggle shadows on and off too.

It's much simpler than trying to find someone to give you the plan in X14. The structure will give you the joist and subfloor. When you open up the room, there is another layer built in that you can adjust the thickness of to give you the finished floor. It is right above what you have highlighted at the 12-5/8" dimension. The default is 3/4" for wood flooring, etc. You can change it to whatever thickness you need, whether 1/2" for tile, 3/8" for engineered flooring, etc To look at it in section will give you the layers of framing, subfloor and finished floor

Each camera has it's own display options. Try turning shadows on for the camera you are using for the interior view

Depending on what is in your library for options, try searching in the library by the keywords "Window Grille." There are several in the catalog that may work for you, including some decorative ones. It is in Pro, if not the others.

A lot of it is common sense and having a way that all of the loads get carried down to the foundation or grade.

I use HD Pro and have since 2013. I've drawn over 730 residential projects with it. One thing to verify is what your state allows designers to draw without being licensed. Here in MA, we can draw any 1-2 family dwelling or addition to. The contractors need to be licensed and insured to build it. They will normally do their own material takeoffs, as I would not rely on the material list from HDP. They all calculate waste in their own way. Regarding engineered material, such LVL, I-joists, roof trusses, etc., most Inspectors want some certified documentation that what I've drawn for those items will work. I design with what should work from information in the materials published span charts. Yet I always note that it is to be verified by others qualified to do. Many of the lumberyards have staff on hand who can take the plans and run the calculations with the software given to them by their engineered material source. Roof trusses are typically designed by the truss manufacturer. A local licensed structural engineer that can take your plan to review and stamp is also a great person to have access to, as some towns will still require a stamped set of drawings. I've never had an issue with drawing the foundation plan and needing an engineer. I hope this helps you a bit.

Select the floor/area that you want to change. Then open up that room and select materials. Take the flooring listed in "Plan Materials" and select it. Then copy it, save it as a name you want to use, then change the pattern and texture to the opposite degree shown, If it's part of a floor that you want to have keep the original direction, then create a room with the new material. Hope this helps

Sure. The polyline does work with the solid white infill

No, I didn't try it, and Eric is correct. I would do the mask on the plan sheet using a polyline and making the lines blank and the infill white. When it's put on the layout, it may creat a blank area for any other pages put over that area. Invisible walls used to work nicely when they were just a single line.

Change the line style to "blank" in the default for the walls you don't want to show. When you open up the line styles, you will see one row that has nothing in it.

Try raising the garage door the needed distance from the floor and adjust the width and height to what is needed to fit the opening. Then check the options to see if you can change the number of panels high it should be

My guess is it has something to do with the room divider issue you posted about earlier. Try opening up the divider and change the wall type to divider and see if the single line will come back.

I've been using Pro since 2013 for my design business and it is more than sufficient for my needs. I design additions, decks, houses, garages, etc. I've used it to produce over 720 plans and construction documents to date.

The tile can be done a couple of ways. Either use the "break wall" tool where the walls intersect and tile just the section you want. Or you can use a soffit made of the tile material you want and manually place it. For the shower you can try searching for "shower hoop" and see if that works for you. There are several items to select from in the library.

You can send someone a direct message

Try reading up on "ceiling planes" and see if it helps

Go to Edit>Default Settings>Floors and Rooms>Room Types. Click "Edit" and the room names will show up in a list. Take one of the numbered bedrooms and Rename it. If you need numbered rooms in your plan, then change the label as David showed in his video for each bedroom type. You can do this for any of the rooms listed. Just check the Edit label too and verify the room has the structure and function you want. There you can edit the materials and structure for the various room types too. Even a room style that is not common in your area can be changed and edited to something you want to have.

There are pre-designed pergola's in the bonus catalogs. Look at a few and see if they will work for you.

Do them as soffits or closed boxes