MarcGaumond

Members
  • Content Count

    6
  • Joined

  • Last visited

Everything posted by MarcGaumond

  1. MarcGaumond

    Staircase baluster and newwl location

    Good day all, Purchase HD Pro 2014 a little than a year ago and worked on it for my verenda project last spring. Now inot trying to complete some interior detail of my house. It is a 2 story house with basement (basement, main floor and second floor). I am trying to replicate my staircases: 1 from the basement to th emain floor and 1 from the main to the second floor. Question is how can I adjust the distance of the newel and balusters from the step edges? Both staircases are against a wall (right side). I have a railing on the left side only. Right now the staircase newel and baluster generated by the tool are too close to the edges of the step. In te case of the basement staircase, the rail on the left side stops at step #4 becasue I have a close wall going to the ceiling for the remaining of the stairs. I can post a picture later when I get back home if more details are required
  2. Using HD Pro2014, can we assign different configuration to each sections of a staricase? I can't seem to find a way to have diffrent width, rails, stinger, winder parameter. It all or nothing. Is this a limitation of HD PRO? If so, which version would allow different settings of different sections? For example, I woul like to have rail on the left side of section 1 & 2; no rail for sections 3 & 4; and so on. Thanks
  3. MarcGaumond

    Staircase baluster and newwl location

    All right, Had some time tonight to play with the model. I erased all stairs and landings and start over. I created a first stairway (1 step), then the main stairway (with 4 sections) and then the landing. After locating the modules in proper location, I strech the landing edges to the adjacent walls (using break lines), I adjusted the stairs width, remove the rail, stringer. I then tried to modify the first step to make it at 45deg (using the Alt key and dragging the first stair anchor points). This is the best I could do for now. I tried to turn on the winder feature for the first section only to make the first step strech to the right wall corner. Unfortunately, this could not be done because all the 4 sections winder check box also turned on. Seems I cannot turn on the winder for only a specific section. When doing this, the second step stretched to the left wall making the model useless. Same thing happened when I tried to turn back on the rail on the left side of the stairway. It created funny figures at the bottom. I will next try to recreate the room below the stair (where the water tank is located) and create the stairway next. I might just create the main to second floor stairway with the open below feature on. I guess this should open the main floor below for the basement stair to appear on the main floor view. Here's what I have now. Going to bed now as it is almost midnight. Thanks again for your help. Will keep you updated.
  4. MarcGaumond

    Staircase baluster and newwl location

    Thanks Mick for offering the opportunity to look at my model. I started the model last year to get to my project for the backyard veranda. An experienced eye will find probably few instances of bad modeleing technique. Has issues with the roof, the pool stairs, the cheminey. Now trying to complete the interior details for the remodeling of the second floor bathroom. Need to add the stairways. I have started with the basement to main floor stairway and then planning to move to the main-second floor stairway . I have tried to create the basement stairway as 1 stairway with 3 sections but for some reason it didnt worked out as planned. Section 1 was for the 45deg first step; Section 2 for the next 3 steps before the closed left side wall; Section 3 for the remaining steps landing at the first floor. The basement stairway is sitting on a small "landing zone" which is 5 inches higher than the basement main floor. The idea was for the main stairway to start from that "landing zone" level but it did not work. Instead it started from the basement floor (as did all stairway I created thereafter). It also created separate individual staircase. Thanks again for all support and help. MGaumond 2015V1.plan
  5. MarcGaumond

    Staircase baluster and newwl location

    Ok here's the picture of the basement stair (P1030676) and the current model snap shot (Stair basement 1). Notice the newel sitting on the first straight step (second if you include the 45deg step) and the half newel at the wall intersection. In the model, the newel is sitting at the corner of the second step so close to the edge that it cuts the raiser, the stringer and the step. I could not locate the half newel at the wall intersection (forth step). Also notice the handrail is not center to the wall but on the outside edge. I will now try the rail wall option.
  6. MarcGaumond

    Staircase baluster and newwl location

    Great, I will try this when back at home and try to add pictures of the model and the actual staircase. Just to try to clarify what I was trying to explain by "being too close to the edges of the steps": The newel is sitting on the second step (the first step is at 45deg from the stair and does not have space for a newel). However, because it is too close to the edge, it is represented going through the step, the stringer and the raiser below. Also the rail does not line up with the center of wall thickness at step #4 Difficult to explain but I will post pictures. Thanks again for the quick reply.