mdag28

Thank you very much for the quick response, Eric. I am back in business. Displaying the DEED layer and deleting it fixed it. I imported a DWG and selected Convert To terrain perimeter for the DEED layer. I think that's when things went wrong. Thanks again and I really appreciate the fix!

Thanks a lot. Looking forward to seeing the fix.

Okay I tried that by selecting Build Terrain and still same result. It's like it's still there or the program thinks it is, but I can't find it.

I build a terrain and then deleted it. Now, the terrain perimeter button is greyed out and I followed the troubleshooting article Troubleshooting Why the Terrain Tools are Greyed Out (homedesignersoftware.com), with the issue still. I also checked my Display Options and terrain perimeter is selected. I have attached my plan file if anyone would like to look into it. This started when I tried to delete the terrain. I went into the 3D view and selected the terrrain, then delete. Patio.plan

Thanks for this solution!

When I change my wall type from Siding-6 to Brick-4 the dimensions of the foundation are increasing, which is not what I want. I want to keep my foundation dimensions unchanged. Is there a way to do this?

I have an electronic PDF of a house plan that I want to recreate in Home Designer. The PDF consists of a foundation plan and a first floor plan. The foundation plan looked the easiest to trace so I started there. However, it appears that after tracing the foundation plan it doesn't automatically make walls on the first floor. Should I redo this and trace the first floor plan or is there a way to get the first floor to produce?

I tried that and it still leaves me with one side that isn't oriented the right direction. I copied and changed to 90 degrees. It is the back of the "cabinet" that is oriented differently than the rest of it.

Good afternoon, I am trying to change the direction of the brick material on one side of a knee high wall. It has the bricks stacked on their short edge, but it should be stacked on long edge. I made it out of a base cabinet. I tried using the Adjust Material Definition command, but it adjusted it for the entire wall. I have the same issue for the vertical separation for the counter made adjacent to the outside wall. Is their a way to adjust one side of the wall only? It needs to match the direction of the fireplace brick. It seems like one of the faces is oriented differently than the other. Covered Patio 21x30.zip I zipped the plan file and attached it. Thanks for looking at my post. Michael

Than you very much Solver and David! You both helped tremendously and I was able to build it correctly. Thanks for taking the time.

I'm trying to show raised tie trusses for my covered outdoor patio using the Home Designer Training video attached below. I'm planning to build custom trusses as shown starting at time 5:08. I don't make it that far as I'm getting an error message that the roof and ceiling planes cannot be found or they are too close together. I believe that the roof and ceiling planes are present so is there a way to increase the space between the roof and ceiling in order for the truss to be built? Also, I noticed that my ceiling surface isn't showing or is not showing in the correct location as can be seen with the mounting location of the ceiling fan and recessed lighting. I've checked the layer display settings and it is toggled ON. Also, my plan is attached. Covered Patio 21x30.zip Video Guide : https://www.homedesignersoftware.com/videos/watch/2250/framing-trusses.html Thank you, Michael Warning Message Example Truss Ceiling Position Issue Roof Plane Spec Covered Patio 21x30.zip

Thank you both DJP and Eric. Your responses have helped me a lot and solves my problem.

I'm having difficulty dimensioning a cross-section. I can't figure out the proper snap and/or dimension settings to dimension from the bottom of the brown framing to the top of the white column. I've checked my default snap and dimension settings and can't get anything to show this. I want to measure this so I can move the framing up and rest on top of the column. This is from a larger file and is for a porch roof and beam that was drawn manually. In order to raise the porch roof planes and beams, I need this measurement. Thank you Brick_base.plan

Thank you DJP! This works pretty well and simulates what I'm trying to do.

I want to add a rowlock brick edge to the top part of a brick base like the rowlock.png shows. The attached plan file and brick.png has the brick base and a column. I want the top row of bricks to be oriented for a rowlock. Is this something that can be done? Brick_base.plan